centos 配置vlan端口
vconfig 在epel源中:
-
安裝vlan(vconfig)和加載8021q模塊
[root@test0001~]#yum install vconfig
[root@test0001~]#modprobe 8021q
[root@test0001~]#lsmod |grep -i 8021q -
在eth0接口上配置兩個VLAN
[root@test0001~]#vconfig add eth0 100
Added VLAN with VID == 100 to IF -:eth0:-
[root@test0001~]#vconfig add eth0 200
Added VLAN with VID == 200 to IF -:eth0:- -
設置VLAN的REORDER_HDR參數,默認就行了
可以使用cat /proc/net/vlan/eth0.100查看eth0.100 參數
[root@test0001~]#vconfig set_flag eth0.100 1 1
Set flag on device -:eth0.100:- Should be visible in /proc/net/vlan/eth0.100
[root@test0001~]#vconfig set_flag eth0.200 1 1
Set flag on device -:eth0.200:- Should be visible in /proc/net/vlan/eth0.200 -
配置網絡信息
[root@test0001~]#ifconfig eth0 0.0.0.0
[root@test0001~]#ifconfig eth0.100 172.16.1.8 netmask 255.255.255.0 up
[root@test0001~]#ifconfig eth0.200 172.16.2.8 netmask 255.255.255.0 up - 刪除VLAN命令
[root@test0001~]#vconfig rem eth0.100
Removed VLAN -:eth0.100:-
[root@test0001~]#vconfig rem eth0.200
Removed VLAN -:eth0.200:-
#將VLAN信息寫入配置文件(/etc/rc.local)中,下次隨機啓動。
#也可以寫入vlan接口的配置文件,指定要橋接的邏輯網橋
例如:
-
#cat ifcfg-em2.12
DEVICE=em2.12
TYPE=ethernet
BOOTPROTO=static
ONBOOT=yes
VLAN=yes
BRIDGE=br12 - #cat /etc/sysconfig/network-scripts/ifcfg-br12
DEVICE=br12
TYPE=bridge
BOOTPROTO=static
ONBOOT=yes
說明:這裏生成vlan接口只爲解決單網卡物理機,創建三網卡虛擬機之目的 (vlan接口 ----- 橋接到對應的br# 下, -----kvm虛擬機生成時指定橋接到不通的虛擬網橋)
POST--->ramfs---->內核--->/etc/inittab--->/etc/rc.d/rc.sysinit--->/etc/rc.d/rc#.d
linux啓動時,先加載內核,然後加載inittab文件,inittab文件中有個條目si::sysinit:/etc/rc.d/rc.sysinit指定了下一個要加載的文件rc.sysinit,這個文件加載完之後,加載/etc/rc.d/rc.RUNLEVEL.d目錄中的啓動腳本,最載/etc/rc.d/rc.local文件。
在rc.RUNLEVEL.d文件夾裏,所存的都是軟鏈接,鏈接到 /etc/rc.d/init.d中的腳本文件,而/etc/rc.d/init.d文件夾和/etc/init.d文件夾是一樣的,/etc/init.d其實是軟鏈接到/etc/rc.d/init.d文件夾中。
假設你有一個腳本,你需要它開機啓動,有2個方法,
第一,就是把它註冊爲系統服務,也就是把它放到/etc/init.d目錄下,並且在腳本中,加一行# chkconfig: 345 85 35,然後就可以用chkconfig命令讓其開機啓動。因爲在/etc/init.d目錄下,所以也可以用service命令控制該腳本。
第二,就是在/etc/rc.d/rc.local文件中,直接把該腳本的路徑寫進去,在開機加載rc.local文件的時候,自然會啓動這個腳本。這個腳本就不能用chkconfig和service命令控制。