源碼包：
libpcap-0.8.3.tar.gz rrdtool-1.2.13.tar.gz ntop-3.3.tar.gz
安裝順序：
先libpcap-0.8.3.tar.gz 或rrdtool-1.2.13.tar.gz，後ntop-3.3.tar.gz
安裝libpcap-0.8.3.tar.gz：
[root@localhost test]# tar -zxf libpcap-0.8.3.tar.gz -C /usr/src/
[root@localhost test]# cd /usr/src/libpcap-0.8.3/
[root@localhost libpcap-0.8.3]# ./configure
[root@localhost libpcap-0.8.3]# make && make install
安裝過程中遇到的問題及解決：
① # ./configure 時
configure: error: Your operating system's lex is insufficient to compile
libpcap. flex is a lex replacement that has many advantages, including
being able to compile libpcap. For more information, see
http://www.gnu.org/software/flex/flex.html .
解決辦法# yum install flex -y，然後再執行 ./configure
② # make && make install時
make: yacc：命令未找到
make: *** [grammar.c] 錯誤 127
解決辦法# yum install byacc -y，然後再編譯安裝make && make install
安裝rrdtool-1.2.13.tar.gz：
[root@localhost test]# tar -zxf rrdtool-1.2.13.tar.gz -C /usr/src/
[root@localhost test]# cd /usr/src/rrdtool-1.2.13/
[root@localhost rrdtool-1.2.13]#./configure --prefix=/usr/local/
[root@localhost rrdtool-1.2.13]#make && make install
安裝ntop-3.3.tar.gz：
[root@localhost test]#tar -zxf ntop-3.3.tar.gz -C /usr/src/
[root@localhost test]#cd /usr/src/ntop-3.3/
[root@localhost ntop-3.3]#./configure --prefix=/usr/local/
[root@localhost ntop-3.3]# make && make install
[root@localhost ntop-3.3]# ntop -A
Please enter the password for the admin user: 設置密碼
Please enter the password again:
Passwords don't match. Please try again.
[root@localhost ntop-3.3]# ntop -d -u nobody -w 9000 -i eth0
在瀏覽器中輸入http:// ip:端口，進入ntop界面：
安裝過程中遇到的問題及解決：
無法找到configure腳本：
解決辦法：
# yum install automake autoconf -y
① ./autogen.sh --disable-mysql
又報：You must have libtool installed to compile ntop.
Download the appropriate package for your distribution, or get the source
tarball from ftp://ftp.gnu.org/pub/gnu/libtool
解決：# yum install libtool -y，再./autogen.sh --disable-mysql
又報：configure: error: C++ preprocessor "/lib/cpp" fails sanity check
解決：# yum install gcc* -y，再./autogen.sh --disable-mysql
又報：
ERROR: gdbm header or library routines are missing
* (yes means it was found, no means it was not found)
*
* gdbm.h...no
* gdbm_open() in -lgdbm...no
*
*>>> No way to proceed.
*
*??? 1. Install libgdbm
*??? and Rerun ./configure
*??? or 2. Use the --with-gdbm-xxxxx= options
*
*******************************************************************
configure: error: Unable to continue... aborting ./configure
解決：# yum install gdbm-devel -y，再./autogen.sh --disable-mysql
② [root@localhost ntop-3.3]# autoconf
[root@localhost ntop-3.3]# automake
就生成了configure腳本，再繼續./configure