switch(config)# hostname hostname
在基於CLI的交換機上設置主機名/系統名:
switch(enable) set system name name-string
2.在基於IOS的交換機上設置登錄口令:
switch(config)# enable password level 1password
在基於CLI的交換機上設置登錄口令:
switch(enable) set password
switch(enable) set enalbepass
3.在基於IOS的交換機上設置遠程訪問:
switch(config)# interface vlan 1
switch(config-if)# ip address ip-addressnetmask
switch(config-if)# ip default-gatewayip-address
在基於CLI的交換機上設置遠程訪問:
switch(enable) set interface sc0 ip-addressnetmask broadcast-address
switch(enable) set interface sc0 vlan
switch(enable) set ip route default gateway
4.在基於IOS的交換機上啓用和瀏覽CDP信息:
switch(config-if)# cdp enable
switch(config-if)# no cdp enable
爲了查看Cisco鄰接設備的CDP通告信息:
switch# show cdp interface [type modle/port]
switch# show cdp neighbors [typemodule/port] [detail]
在基於CLI的交換機上啓用和瀏覽CDP信息:
switch(enable) set cdp {enable|disable}module/port
爲了查看Cisco鄰接設備的CDP通告信息:
switch(enable) show cdpneighbors[module/port] [vlan|duplex|capabilities|detail]
5.基於IOS的交換機的端口描述:
switch(config-if)# descriptiondescription-string
基於CLI的交換機的端口描述:
switch(enable)set port name module/numberdescription-string
6.在基於IOS的交換機上設置端口速度:
switch(config-if)# speed{10|100|auto}
在基於CLI的交換機上設置端口速度:
switch(enable) set port speed moudle/number{10|100|auto}
switch(enable) set port speed moudle/number{4|16|auto}
7.在基於IOS的交換機上設置以太網的鏈路模式:
switch(config-if)# duplex {auto|full|half}
在基於CLI的交換機上設置以太網的鏈路模式:
switch(enable) set port duplexmodule/number {full|half}
8.在基於IOS的交換機上配置靜態VLAN:
switch# vlan database
switch(vlan)# vlan vlan-num name vla
switch(vlan)# exit
switch# configure teriminal
switch(config)# interface interfacemodule/number
switch(config-if)# switchport mode access
switch(config-if)# switchport access vlanvlan-num
switch(config-if)# end
在基於CLI的交換機上配置靜態VLAN:
switch(enable) set vlan vlan-num [namename]
switch(enable) set vlan vlan-nummod-num/port-list
9. 在基於IOS的交換機上配置VLAN中繼線:
switch(config)# interface interfacemod/port
switch(config-if)# switchport mode trunk
switch(config-if)# switchport trunkencapsulation {isl|dotlq}
switch(config-if)# switchport trunk allowedvlan remove vlan-list
switch(config-if)# switchport trunk allowedvlan add vlan-list
在基於CLI的交換機上配置VLAN中繼線:
switch(enable) set trunk module/port[on|off|desirable|auto|nonegotiate]
Vlan-range [isl|dotlq|dotl0|lane|negotiate]
10.在基於IOS的交換機上配置VTP管理域:
switch# vlan database
switch(vlan)# vtp domain domain-name
在基於CLI的交換機上配置VTP管理域:
switch(enable) set vtp [domain domain-name]
11.在基於IOS的交換機上配置VTP 模式:
switch# vlan database
switch(vlan)# vtp domain domain-name
switch(vlan)# vtp{sever|cilent|transparent}
switch(vlan)# vtp password password
在基於CLI的交換機上配置VTP 模式:
switch(enable) set vtp [domain domain-name][mode{ sever|cilent|transparent }][password password]
12. 在基於IOS的交換機上配置VTP版本:
switch# vlan database
switch(vlan)# vtp v2-mode
在基於CLI的交換機上配置VTP版本:
switch(enable) set vtp v2 enable
13. 在基於IOS的交換機上啓動VTP剪裁:
switch# vlan database
switch(vlan)# vtp pruning
在基於CL I 的交換機上啓動VTP剪裁:
switch(enable) set vtp pruning enable
14.在基於IOS的交換機上配置以太信道:
switch(config-if)# port group group-number[distribution {source|destination}]
在基於CLI的交換機上配置以太信道:
switch(enable) set port channelmoudle/port-range mode{on|off|desirable|auto}
15.在基於IOS的交換機上調整根路徑成本:
switch(config-if)# spanning-tree [vlanvlan-list] cost cost
在基於CLI的交換機上調整根路徑成本:
switch(enable) set spantree portcostmoudle/port cost
switch(enable) set spantree portvlancostmoudle/port [cost cost][vlan-list]
16.在基於IOS的交換機上調整端口ID:
switch(config-if)# spanning-tree[vlanvlan-list]port-priority port-priority
在基於CLI的交換機上調整端口ID:
switch(enable) set spantree portpri{mldule/port}priority
switch(enable) set spantree portvlanpri{module/port}priority [vlans]
17. 在基於IOS的交換機上修改STP時鐘:
switch(config)# spanning-tree [vlanvlan-list] hello-time seconds
switch(config)# spanning-tree [vlanvlan-list] forward-time seconds
` switch(config)# spanning-tree [vlanvlan-list] max-age seconds
在基於CLI的交換機上修改STP時鐘:
switch(enable) set spantree hello interval[vlan]
switch(enable) set spantree fwddelay delay[vlan]
switch(enable) set spantree maxageagingtiame[vlan]
18. 在基於IOS的交換機端口上啓用或禁用PortFast 特徵:
switch(config-if)#spanning-tree portfast
在基於CLI的交換機端口上啓用或禁用Port Fast 特徵:
switch(enable) set spantree portfast{module/port}{enable|disable}
19. 在基於IOS的交換機端口上啓用或禁用UplinkFast特徵:
switch(config)# spanning-tree uplinkfast[max-update-rate pkts-per-second]
在基於CLI的交換機端口上啓用或禁用UplinkFast 特徵:
switch(enable) set spantree uplinkfast{enable|disable}[rate update-rate] [all-protocols off|on]
20. 爲了將交換機配置成一個集羣的命令交換機,首先要給管理接口分配一個IP地址,然後使用下列命令:switch(config)# cluster enable cluster-name
21. 爲了從一條中繼鏈路上刪除VLAN,可使用下列命令:
switch(enable) clear trunk module/portvlan-range
22. 用show vtp domain 顯示管理域的VTP參數.
23. 用show vtp statistics顯示管理域的VTP參數.
24. 在Catalyst交換機上定義TrBRF的命令如下:
switch(enable) set vlan vlan-name [namename] type trbrf bridge bridge-num[stp {ieee|ibm}]
25. 在Catalyst交換機上定義TrCRF的命令如下:
switch (enable) set vlan vlan-num [namename] type trcrf
{ring hex-ring-num|decringdecimal-ring-num} parent vlan-num
26. 在創建好TrBRF VLAN之後,就可以給它分配交換機端口.對於以太網交換,可以採用如下命令給VLAN分配端口:
switch(enable) set vlan vlan-nummod-num/port-num
27. 命令show spantree顯示一個交換機端口的STP狀態.