1、實驗拓撲
2、PC配置
3、將PC1和PC2劃分爲同一個vlan10,實現vlan10內的通信
（1）配置交換機SW1
[SW1]vlan batch 10 20
Info: This operation may take a few seconds. Please wait for a moment...done.
[SW1]interface e0/0/10
[SW1-Ethernet0/0/10]port link-type access
[SW1-Ethernet0/0/10]port default vlan 10
[SW1-Ethernet0/0/10]interface e0/0/11
[SW1-Ethernet0/0/11]port link-type access
[SW1-Ethernet0/0/11]port default vlan 10
[SW1-Ethernet0/0/11]interface e0/0/1
[SW1-Ethernet0/0/1]port link-type access
[SW1-Ethernet0/0/1]port default vlan 10
（2）測試PC1和PC2連通性
4、在R1上配置IP地址使得R1能與PC1和PC2通信
（1）路由器AR1配置
[AR1]interface g0/0/1
[AR1-GigabitEthernet0/0/1]ip add 192.168.10.254 24
5、實現AR3與PC3的通信
（1）交換機SW2配置
[SW2]vlan batch 10 20
Info: This operation may take a few seconds. Please wait for a moment...done.
[SW2]interface e0/0/1
[SW2-Ethernet0/0/1]port hybrid pvid vlan 20
[SW2-Ethernet0/0/1]port hybrid untagged vlan all
[SW2-Ethernet0/0/1]interface e0/0/10
[SW2-Ethernet0/0/10]port hybrid pvid vlan 20
[SW2-Ethernet0/0/10]port hybrid untagged vlan all
[SW2-Ethernet0/0/10]
（2）路由器AR3配置
[Huawei]sysname AR3
[AR3]interface g0/0/2
[AR3-GigabitEthernet0/0/2]ip add 192.168.3.254 24
6、靜態路由
（1）在AR1,AR2,AR3配置IP地址
[AR1]interface g0/0/0
[AR1-GigabitEthernet0/0/0]ip add 12.12.12.1 24
[Huawei]sysname AR2
[AR2]interface g0/0/0
[AR2-GigabitEthernet0/0/0]ip add 12.12.12.2 24
[AR2-GigabitEthernet0/0/0]interface g0/0/1
[AR2-GigabitEthernet0/0/1]ip add 23.23.23.2 24
[AR3]interface g0/0/1
[AR3-GigabitEthernet0/0/1]ip add 23.23.23.3 24
（2）配置完IP後測試直連網段的通斷
[AR1]ping 12.12.12.2
PING 12.12.12.2: 56 data bytes, press CTRL_C to break
Reply from 12.12.12.2: bytes=56 Sequence=1 ttl=255 time=80 ms
Reply from 12.12.12.2: bytes=56 Sequence=2 ttl=255 time=50 ms
Reply from 12.12.12.2: bytes=56 Sequence=3 ttl=255 time=40 ms
Reply from 12.12.12.2: bytes=56 Sequence=4 ttl=255 time=10 ms
Reply from 12.12.12.2: bytes=56 Sequence=5 ttl=255 time=30 ms
--- 12.12.12.2 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 10/42/80 ms
[AR2]ping 23.23.23.3
PING 23.23.23.3: 56 data bytes, press CTRL_C to break
Reply from 23.23.23.3: bytes=56 Sequence=1 ttl=255 time=70 ms
Reply from 23.23.23.3: bytes=56 Sequence=2 ttl=255 time=30 ms
Reply from 23.23.23.3: bytes=56 Sequence=3 ttl=255 time=60 ms
Reply from 23.23.23.3: bytes=56 Sequence=4 ttl=255 time=10 ms
Reply from 23.23.23.3: bytes=56 Sequence=5 ttl=255 time=50 ms
--- 23.23.23.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 10/44/70 ms
（3）使用靜態實現AR1到AR3的互通
（1） 配置AR1到AR3的靜態路由
- [AR1]ip route-static 23.23.23.0 24 12.12.12.2
- （格式：ip route-static <目的網段或目的IP> <掩碼> <下一跳IP地址或出接口號>） 使用tracert命令驗證，AR1能通過AR2到達AR3，由於AR1和AR2是直連的，所以在到達AR2時返回數據，但之後就不通了。
[AR1]ip route-static 23.23.23.0 24 12.12.12.2
[AR1]tracert 23.23.23.3
traceroute to 23.23.23.3(23.23.23.3), max hops: 30 ,packet length: 40,press CT
RL_C to break
1 12.12.12.2 40 ms 50 ms 30 ms
2 * * *
3 * * *
4 * * *
5 * * *
原因：AR1有到達AR3的路由，但是AR3並不知道如何到達AR1
（2） 配置AR3到AR1的靜態路由
- [AR3]ip route-static 12.12.12.0 24 23.23.23.2
[AR3]ip route-static 12.12.12.0 24 23.23.23.2
測試：
[AR1]ping 23.23.23.3
PING 23.23.23.3: 56 data bytes, press CTRL_C to break
Reply from 23.23.23.3: bytes=56 Sequence=1 ttl=254 time=70 ms
Reply from 23.23.23.3: bytes=56 Sequence=2 ttl=254 time=60 ms
Reply from 23.23.23.3: bytes=56 Sequence=3 ttl=254 time=30 ms
Reply from 23.23.23.3: bytes=56 Sequence=4 ttl=254 time=60 ms
Reply from 23.23.23.3: bytes=56 Sequence=5 ttl=254 time=30 ms
--- 23.23.23.3 ping statistics ---
5 packet(s) transmitted
5 packet(s) received
0.00% packet loss
round-trip min/avg/max = 30/50/70 ms
[AR1]tracert 23.23.23.3
traceroute to 23.23.23.3(23.23.23.3), max hops: 30 ,p
acket length: 40,press CTRL_C to break
1 12.12.12.2 50 ms 50 ms 40 ms
2 23.23.23.3 70 ms 60 ms 60 ms
7、配置實現全網段的互通
（1）要求1：AR1能到達192.168.3.0/24網段
[AR1]ip route-static 192.168.3.0 24 12.12.12.2
[AR2]ip route-static 192.168.3.0 24 23.23.23.3
測試：
[AR1]tracert 192.168.3.3
traceroute to 192.168.3.3(192.168.3.3), max hops: 30 ,packet length: 40,press
CTRL_C to break
1 12.12.12.2 40 ms 50 ms 50 ms
2 23.23.23.3 60 ms 60 ms 60 ms
3 192.168.3.3 110 ms 100 ms 110 ms
（2）要求2：AR3能到達192.168.12.0/24網段
[AR3]ip route-static 192.168.10.0 24 23.23.23.2
[AR2]ip route-static 192.168.10.0 24 12.12.12.1
測試：
[AR3]tracert 192.168.10.1
traceroute to 192.168.10.1(192.168.10.1), max hops: 30 ,packet length: 40,pres
s CTRL_C to break
1 23.23.23.2 10 ms 50 ms 50 ms
2 12.12.12.1 60 ms 60 ms 70 ms
3 192.168.10.1 110 ms 100 ms 130 ms
8、在PC1或PC2上ping PC3觀察是否實現全互通
9、查看各個路由器的路由表
AR1：
[AR1]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 9 Routes : 9
Destination/Mask Proto Pre Cost Flags NextHop Interface
12.12.12.0/24 Direct 0 0 D 12.12.12.1 GigabitEthernet
0/0/0
12.12.12.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
19.168.3.0/24 Static 60 0 RD 12.12.12.2 GigabitEthernet
0/0/0
23.23.23.0/24 Static 60 0 RD 12.12.12.2 GigabitEthernet
0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.3.0/24 Static 60 0 RD 12.12.12.2 GigabitEthernet
0/0/0
192.168.10.0/24 Direct 0 0 D 192.168.10.254 GigabitEthernet
0/0/1
192.168.10.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
AR2：
[AR2]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 8 Routes : 8
Destination/Mask Proto Pre Cost Flags NextHop Interface
12.12.12.0/24 Direct 0 0 D 12.12.12.2 GigabitEthernet
0/0/0
12.12.12.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
23.23.23.0/24 Direct 0 0 D 23.23.23.2 GigabitEthernet
0/0/1
23.23.23.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.3.0/24 Static 60 0 RD 23.23.23.3 GigabitEthernet
0/0/1
192.168.10.0/24 Static 60 0 RD 12.12.12.1 GigabitEthernet
0/0/0
AR3：
[AR3]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 8 Routes : 8
Destination/Mask Proto Pre Cost Flags NextHop Interface
12.12.12.0/24 Static 60 0 RD 23.23.23.2 GigabitEthernet
0/0/1
23.23.23.0/24 Direct 0 0 D 23.23.23.3 GigabitEthernet
0/0/1
23.23.23.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.3.0/24 Direct 0 0 D 192.168.3.254 GigabitEthernet
0/0/2
192.168.3.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.10.0/24 Static 60 0 RD 23.23.23.2 GigabitEthernet
0/0/1