在點到多點非廣播模式下，必須靜態指定鄰居。
配置如同point-to-multipoint模式下，只是在指定OSPF網絡類型時，使用命令ip ospf network point-to-multipoint non-broadcast，此時由於無法啓用組播和廣播，所以無法自動建立鄰居關係，需要手工指定鄰居。仍不選舉DR/BDR
FR：
FR(config)#no ip routing
FR(config)#frame-relay switching
FR(config)#int s0/0
FR(config-if)#no ip add
FR(config-if)#no sh
FR(config-if)#en fr
FR(config-if)#frame-relay intf-ty dce
FR(config-if)#clock rate 64000
FR(config-if)#frame-relay lmi-type cisco
FR(config-if)#frame-relay route 102 int s0/1 201
FR(config-if)#frame-relay route 103 int s0/2 301
FR(config-if)#exit
FR(config)#int s0/1
FR(config-if)#no sh
FR(config-if)#no ip add
FR(config-if)#en fr
FR(config-if)#frame-relay intf-type dce
FR(config-if)#clock rate 64000
FR(config-if)#frame-relay lmi-type cisco
FR(config-if)#frame-relay route 201 int s0/0 102
FR(config-if)#exit
FR(config)#int s0/2
FR(config-if)#no ip add
FR(config-if)#no sh
FR(config-if)#en fr
FR(config-if)#frame-relay intf-ty dce
FR(config-if)#clock rate 64000
FR(config-if)#frame-relay lmi-type cisco
FR(config-if)#frame-relay route 301 int s0/0 103
FR(config-if)#exit
R1：
R1(config)#int lo0
R1(config-if)#ip add 1.1.1.1 255.255.255.0
R1(config-if)#ip ospf net point-to-point
R1(config-if)#exit
R1(config)#int s0/0
R1(config-if)#no ip add
R1(config-if)#no sh
R1(config-if)#en fra
R1(config)#int s0/0.1 multipoint
R1(config-subif)#ip add 10.10.10.1 255.255.255.0
R1(config-subif)#frame-relay map ip 10.10.10.2 102 br
R1(config-subif)#frame-relay map ip 10.10.10.3 103 br
R1(config-subif)#ip ospf net point-to-multipoint non-broadcast
R1(config)#router ospf 1
R1(config-router)#router-id 1.1.1.1
R1(config-router)#net 1.1.1.0 0.0.0.255 area 0
R1(config-router)#net 10.10.10.0 0.0.0.255 area 0
R1(config-router)#neighbor 10.10.10.2 //手工指定鄰居
R1(config-router)#neighbor 10.10.10.3
R1(config-router)#exit
R2：
R2(config)#int lo 0
R2(config-if)#ip add 2.2.2.2 255.255.255.0
R2(config-if)#ip ospf net point-to-point
R2(config-if)#exit
R2(config)#int s0/0
R2(config-if)#ip add 10.10.10.2 255.255.255.0
R2(config-if)#no sh
R2(config-if)#encapsulation frame-relay
R2(config-if)#frame-relay map ip 10.10.10.1 201 br
R2(config-if)#ip ospf net point-to-multipoint non-broadcast
R2(config)#router ospf 1
R2(config-router)#router-id 2.2.2.2
R2(config-router)#net 2.2.2.0 0.0.0.255 area 0
R2(config-router)#net 10.10.10.0 0.0.0.255 area 0
R2(config-router)#exit
R3：
R2(config)#int lo 0
R2(config-if)#ip add 3.3.3.3 255.255.255.0
R2(config-if)#ip ospf net point-to-point
R2(config-if)#exit
R3(config)#int s0/0
R3(config-if)#ip add 10.10.10.3 255.255.255.0
R3(config-if)#no sh
R3(config-if)#encapsulation frame-relay
R3(config-if)#frame-relay map ip 10.10.10.1 301 br
R3(config-if)#ip ospf net point-to-multipoint non-broadcast
R3(config)#router ospf 1
R3(config-router)#router-id 3.3.3.3
R3(config-router)#net 3.3.3.0 0.0.0.255 area 0
R3(config-router)#net 10.10.10.0 0.0.0.255 area 0
R3(config-router)#exit
驗證：
R1#sh ip ospf int s0/0.1
Serial0/0.1 is up, line protocol is up
Internet Address 10.10.10.1/24, Area 0
Process ID 1, Router ID 1.1.1.1, Network Type POINT_TO_MULTIPOINT, Cost: 64
Transmit Delay is 1 sec, State POINT_TO_MULTIPOINT,
Timer intervals configured, Hello 30, Dead 120, Wait 120, Retransmit 5
oob-resync timeout 120
Hello due in 00:00:14
Supports Link-local Signaling (LLS)
Index 2/2, flood queue length 0
Next 0x0(0)/0x0(0)
Last flood scan length is 1, maximum is 2
Last flood scan time is 0 msec, maximum is 4 msec
Neighbor Count is 2, Adjacent neighbor count is 2
Adjacent with neighbor 3.3.3.3
Adjacent with neighbor 2.2.2.2
Suppress hello for 0 neighbor(s)
R2#sh ip ro os
1.0.0.0/24 is subnetted, 1 subnets
O 1.1.1.0 [110/65] via 10.10.10.1, 00:03:55, Serial0/0
3.0.0.0/24 is subnetted, 1 subnets
O 3.3.3.0 [110/129] via 10.10.10.1, 00:03:55, Serial0/0
10.0.0.0/8 is variably subnetted, 3 subnets, 2 masks
O 10.10.10.3/32 [110/128] via 10.10.10.1, 00:03:55, Serial0/0
O 10.10.10.1/32 [110/64] via 10.10.10.1, 00:03:55, Serial0/0